DMS SEALS TECHNOLOGY CO.,LIMITED

Site map

The Professional Sealing Solution Supplier.

Mail to: sales@dmsseals.com

TEL:+86-757-86235767

Home  >  Top PRODUCTS  >  Quality Spring Seals  >  spring energized seals seal spring energized seals DMS Seal Manufacturer Brand
spring energized seals seal spring energized seals DMS Seal Manufacturer Brand

spring energized seals seal spring energized seals DMS Seal Manufacturer Brand

Diameter Range
3~1600mm
Pressure Range
40MPa
Temperature Range
-40℃ +260℃
Speed
15m/s
Medium
all liquids, chemicals and gases
Company Advantages
1. Quality control of the seals is the basis for DMS Seals. DMS Seal Manufacturer material for spring energized seals is different from other companies' material and it's better.
2. Seal we produced has applications in a wide range of fields. DMS Seal Manufacturer will promote innovation work, and strive to develop more, newer and better products.
3. We have developed solutions of the sealing of special working condition. Different types of spring energized seals,spring loaded seal allow more choices to design oil seal spring.

DMS Seal Manufacturer-Find Spring Energized Seals oil Seal Manufacturer On Dms Seal Manufacturer

1. Application and properties

Suitable for reciprocating piston rod or piston single acting seal, the working pressure has a wide range of adaptability, and the pressure capacity can be enhanced by increasing the tail length size or increasing the check ring.

Small friction coefficient, The contact pressure between the mating surface and the mating surface is low, and the friction between the work face and the mating surface is the smallest in all seal types. with or without lubrication can work, wear resistance, long service life.

The working medium of the sealing sleeve has wide adaptability, and the other chemicals are not reacted except soluble alkali metal, high temperature fluorine gas and three fluoride chloride.

The working temperature range is wide, and can be used for -200 ℃ to +250 ℃.

It can be used for very high speed, very low speed, micro-stroke and other special conditions.

Suitable for aviation, military and industrial sealing groove size, The standard installation groove is the same size as the standard O ring, and the size is small. It can be designed as non standard parts to meet the sealing requirements of any size groove. The groove is open or semi open.

It can be used in rotary sealing. It can adapt to large eccentricity and beating.


2. Standard materials

Sealing sleeve: PTFE

Spring: Stainless steel 304, 316


3. Working Conditions

Working  Conditions

Diameter Range

Pressure Range

Temperature Range 

Speed

Medium

3 - 1600mm

0 - 20MPa

-200 ~ +250

5 m/s

High and low temperature oil and water and other fluids.


4. 
Installation Sizes

Back pressure surfaceR1=0.1 ~ 0.2, tank bottom R2=0.3 ~ 0.5, Import lengthC=(0.7 ~ 1.0)L.

Rod Diameter

 

Groove Width

Groove Diameter

Radial Clearance

 

d

L

D

e

2 ~ 10

2.5

d+3.0

0.05

10 ~ 22

3.2

d+4.0

0.065

22 ~ 52

4.7

d+6.0

0.075

48 ~ 150

7.5

d+10.0

0.09

150 ~ 400

11.0

d+15.0

0.10


5. 
Matters needing attention  

Ⅰ, The installation groove must be open or semi open, and it is recommended to be open.

Ⅱ, If the seal is for the rotating shaft, it is recommended that the surface hardness of the shaft should be no less than HRC40.

Considering the adaptability of the working medium, the adaptability of the jacket and spring should be taken into account.

Ⅳ, It is better to install an anti fouling ring or a antifouling guide ring in the notch direction in front of the seal.

 





Company Features
1. Equipped with a complete set of quality control technology, spring energized seals can be guaranteed with good quality.
2. DMS Seal Manufacturer's devotion is to offer the most professional customer service which ranks top in spring seals industry. Call!
Product Message
社媒暂无评论
Contact